thermal cutter, hot knife ,heating cutter,

heating knife, heating trimmer for eva pvb sgp lamination

Peter Lin, cnc@cncGlass.com,

cnc@cncEVA.com

Whatsapp: 0086 15013829504,

WeChat: WeCan365

www_cncGlass_com  www_cncEVA_com

Differences between CNC02 and CNC01:

*CNC02-Continuously-Working Thermal Cutter is designed for continuously working with air cooling system, while CNC01-Intermittently-Working is only for short time working, you need to release the button intermittently for cooling after short time heating in case itself gets too hot.

*CNC02-Continuously-Working is able to trim the edges with minimum of smoke and no burned marks.

*CNC02-Continuously-Working is lighter ,only 610g, easier to handle, while CNC01 is 950g.

*CNC02-Continuously-Working is available for high point temperature adjustment, 16 sections of temp to set. So you don’t need to let the blades going up to 500C degrees each time you use it, you may only set the lower temperature(for example  about 300C degrees) only if it’s high enough for you to trim interlayer remains, so you can prolong the life time of the blades, and save cost.

Peter Lin, cnc@cncGlass.com,

cnc@cncEVA.com

Whatsapp: 0086 15013829504,

WeChat: WeCan365

www_cncGlass_com  www_cncEVA_com

Edges Cleaning hot knife for SGP PVB laminated safety glass

Hand operated tool for cutting small quantities, for short-time operation only.

To cut and seal synthetic fiber products, such as ropes, bands, belts and fabric.  

Fitted with cutting foot, the combined tool is especially effective for cutting

synthetic fabric without cutting surface.

Controlling heating by switching the toll on and off

Peter Lin, cnc@cncGlass.com,

cnc@cncEVA.com

Whatsapp: 0086 15013829504,

WeChat: WeCan365

Hot Knife Electric Rope Cutter Cautions

Always operate the Hot Knife in well ventilated space.

Never burn off the excess residue on the Hot Knife blade. The blades will over heated and be warped.

Only operate Hot Knife when it is in contact with the insulation board

Keep hot blades away from skin, clothing and other flammable materials.

Allow blades to cool before handling. Hot Knife may cause injury or burns to exposed surfaces.

If the temperature inside the tool is too high, the unit will get hot and the internal thermal protectors will turn it off, after it cool, the Hot Knife will operate again.

BLUE SILICONE SHEET
BLUE SILICONE BLANKET
FOR EVA PVB SGP GLASS VACUUMING
Peter Lin, cnc@cncGlass.com,
cnc@cncEVA.com
Whatsapp: 0086 15013829504,
WeChat: WeCan365
www.cncglass.com www.cnceva.com

Silicone rubber sheet for glass industry is a key component of our company dedicated to supporting the glass vacuum laminated furnace according to market demand.
Laminated glass vacuum furnace uses vacuum principle, make the glass heated under vacuum conditions, with the atmospheric pressure, let the glass in the vacuum bag pressed to exclude air and unable to make bubbles, vacuum bag is under heating and vacuum pumped conditions to make two or more pieces of glass and EVA hot together.
Vacuum bag is a core part of glass vacuum laminated furnace, it makes up of two pieces of silicone rubber sheet and silicone sealing edge, silicone rubber sheet is a key component of the entire laminated furnace, its quality directly affects the quality of glass products.

Multi Size Choices Polyester High Temperature Green Powder Coating Masking PET Tape, Ideal for SentryGlas Plus interlayer (SGP)laminated safety glazing RoHS compliant. Withstands heat up to 428℉(220℃) Color: Green, Material: Polyethylene terephthalate (PET), Adhesion Type: Silicone. Leaves no residue after peel away. Excellent electrical insulation,Resistant to abrasion, chemicals and temperature Multi-applications:Primarily used for masking parts during powder coating,painting, plating,anodizing, sublimation,general die-cutting applications,etc. Multiple size value bundle: Including 1/4 inch x 36yds, 1/2 inch x 36yds,3/4 inch x 36yds, 1 inch x 36yds, Meet your different size requirments. 4 rolls (36 yds per roll) Peter Lin, cnc@cncGlass.com, cnc@cncEVA.com Whatsapp: 0086 15013829504, WeChat: WeCan365 www.cncglass.com www.cnceva.com Peter Lin, cnc@cncGlass.com, cnc@cncEVA.com Whatsapp: 0086 15013829504, WeChat: WeCan365 www.cncglass.com www.cnceva.com


Multi Size Choices Polyester High Temperature
Green Powder Coating Masking PET Tape, Ideal
for SentryGlas Plus interlayer (SGP)laminated
safety glazing
RoHS compliant. Withstands heat up to 428℉(220℃)
Color: Green, Material: Polyethylene terephthalate
(PET), Adhesion Type: Silicone. Leaves no residue
after peel away.
Excellent electrical insulation,Resistant to abrasion,
chemicals and temperature
Multi-applications:Primarily used for masking parts
during powder coating,painting, plating,anodizing,
sublimation,general die-cutting applications,etc.
Multiple size value bundle: Including 1/4 inch x 36yds,
1/2 inch x 36yds,3/4 inch x 36yds, 1 inch x 36yds,
Meet your different size requirments. 4 rolls (36 yds per roll)

Peter Lin, cnc@cncGlass.com,
cnc@cncEVA.com
Whatsapp: 0086 15013829504,
WeChat: WeCan365
www.cncglass.com www.cnceva.com

Peter Lin, cnc@cncGlass.com,
cnc@cncEVA.com
Whatsapp: 0086 15013829504,
WeChat: WeCan365
www.cncglass.com www.cnceva.com

Differences between CNC02 and CNC01:

*CNC02-Continuously-Working Thermal Cutter is designed for continuously working with air cooling system, while CNC01-Intermittently-Working is only for short time working, you need to release the button intermittenly for cooling after shor-time heating in case itself gets too hot.

*CNC02-Continuously-Working is able to trim the edges with minimum of smoke and no burned marks.

*CNC02-Continuously-Working is lighter ,only 610kg, easier to hanlde, while CNC01 is 950kg.

*CNC02-Continuously-Working is availbe for high point temperature adjustment,16 sections of temp to set. So you don’t need to let the blades going up to 500C degrees each time you use it, you may only set the lower temperature(for example about 300C degrees) only if it’s high enough for you to trim interlayer remains, so you can prolong the life time of the blades, and save cost.

——————
Peter Lin
cnc@cncGlass.com
Whatsapp: +86 15013829504
WeChat: wecan365
Mobile: +86 15013829504
www.cncglass.com